So I finally got my new/used vehicle yesterday, and measured the box. . .78 inches. Katana length 84 inches. Obviously with the tailgate down, this won't be an issue hauling it. Does anyone actually know the wheelbase length, from wheel to wheel? I would assume it is short enough to fit in the box itself. Also, does anyone haul the kat kitty corner in there box? there is more then enough room to haul it if it goes in that way? or is that a risky maneuver? Thanks for the help guys. By looking at Speedees pic on my last post, it looks like the kat will fit in the box without the tailgate on, but I want reassurance. If it helps my truck is a dodge dakota extended cab.
Ad Widget
Collapse
Announcement
Collapse
No announcement yet.
X
-
We've put my bike in the back of a little Nissan pickup with the gate down a few times , no problems . Putting it in corner to corne sounds REALLY iffy for a few reasons I can think of . For one , when you break , the weight will want to shift forward . With the bike stright on , it's less likely it'll go anywhere . But corner-wise , sliding sideways seems like a real possibility if there's the least bit of slack anywhere in the ropes ...
-
Originally posted by md86We've put my bike in the back of a little Nissan pickup with the gate down a few times , no problems . Putting it in corner to corne sounds REALLY iffy for a few reasons I can think of . For one , when you break , the weight will want to shift forward . With the bike stright on , it's less likely it'll go anywhere . But corner-wise , sliding sideways seems like a real possibility if there's the least bit of slack anywhere in the ropes ...Kan-O-Gixxer!
-89 Gixxer 1100 Engine
-Stage 3 Jet Kit / KNN Pod Filters
-Ohlins Susupension
-Various Other Mods
Comment
-
Originally posted by md86We've put my bike in the back of a little Nissan pickup with the gate down a few times , no problems . Putting it in corner to corne sounds REALLY iffy for a few reasons I can think of . For one , when you break , the weight will want to shift forward . With the bike stright on , it's less likely it'll go anywhere . But corner-wise , sliding sideways seems like a real possibility if there's the least bit of slack anywhere in the ropes ...
1- buy a set of those anchors that go into the holes on the bed rails.
2- put the bike in on an angle and wedge the front tire up into the corner.
3- run a strap through the front rim and draw it up with the front anchor. Just that alone will almost keep the bike standing on it's own, so you have to turn the steering to get the bike to come down on it's kickstand. (put a steel plate or a 1/2 - 3/4 in pc of plywood under the kickstand or it will dent the floor of your box.
4-anchor down the rear nice and tight.
Most of the time I just have 3 straps.....one holding the front wheel secure into the corner.....and 2 holding down the rear. If I am on a long haul, I add two to the front.....for 5 straps total. I have never had an issue with putting my bike in on an angle. In fact, with the front wheel wedged in the corner and the back secured good, it doesn't go anywhere.I don't have a short temper. I just have a quick reaction to bullshit.
Comment
-
Originally posted by md86Well alrighty then ! I don't haul my bike that often , so I guess you know better than I .
I am not saying it is just as good as hauling it straight (I would if I could)....but I will say that it can be hauled at an angle if you do it right and anchor it down with good quality straps and drive accordingly.I don't have a short temper. I just have a quick reaction to bullshit.
Comment
-
With an extended cab, you shouldn't have a problem, the bike should fit with both wheels on the bed, but you probably won't be able to close the tailgate.
The bed on my Colorado should be about the same length as the one on your Dakota, and my bike fit in mine (straight) without a problem, but I couldn't close the tailgate, so I just locked it in at its 45 or 55 degree position (don't remember which one).
In that picture, actually, the back isn't strapped down at all, I only strapped down the front, and didn't have any issues with the bike wanting to move. In fact, if for some reason your rear tire ends up resting on the tailgate instead of the truck bed itself, I would recommend (a) getting a piece of wood to put under the bike's rear tire to distribute the load across the width of the tailgate, and (b) not tying the rear of the bike down very much, if at all, as you could easily put a nice sized dent in your tailgate when you hit bumps. I've seen a few people in the past who've done that on other trucks and been very upset about it laterNick www.naskie18.com Googletalk: naskie18 AIM: naskie18
Comment
Comment