So I had a lot of trouble finding a good wiring diagram that didn't make me want to throw myself into oncoming traffic, all the ones I found the lines just blurred together, and the only one I found that had colors on it, was horribly undersized to read clearly. So here is a pre kat 750 wiring diagram I reworked for those of us that have trouble reading and making sense of the diagrams. Hope it helps
Ad Widget
Collapse
Announcement
Collapse
No announcement yet.
This is a sticky topic.
X
X
-
-Steve
sigpic
Welcome to KatRiders.com! Click here to register
Don't forget to check the Wiki! http://katriders.com/wiki
-
Originally posted by flcmbt View PostSo I had a lot of trouble finding a good wiring diagram that didn't make me want to throw myself into oncoming traffic,
Comment
-
Originally posted by Gregski View Postthanks for taking the time to make it and share it with us1992- project katfighter
2005- GSXR750
2001- TL1000R
http://katriders.com/vb/showthread.php?t=111130
www.lunchtimecigar.com
KATRIDERS RALLY 2014 - cintidude04
KATRIDERS RALLY 2015 - cintidude04
KATRIDERS RALLY 2016 - cintidude04
Comment
-
I could have sworn that there was a pre diagram in there too-Steve
sigpic
Welcome to KatRiders.com! Click here to register
Don't forget to check the Wiki! http://katriders.com/wiki
Comment
-
Several posted in the wiring section as well. I've posted ones for the pre in there least 3 times in the past year.1992- project katfighter
2005- GSXR750
2001- TL1000R
http://katriders.com/vb/showthread.php?t=111130
www.lunchtimecigar.com
KATRIDERS RALLY 2014 - cintidude04
KATRIDERS RALLY 2015 - cintidude04
KATRIDERS RALLY 2016 - cintidude04
Comment
-
I put my fairings back on the bike after some work (they were off for a week). Everything works great except the right front turn signal. There were four connections hanging down from somewhere by the handlebars, but only two connections (black and red from the turn signal). I forget which wires connect with which connectors (and am also surprised that there are two extra connectors...)
Anyways, I looked at the wiring diagram in this post, and I believe that the pink connector wire should go with the Black (with white stripe) wire from the turn signal. The green connector wire should go with the Red wire coming from the turn signal. I have tried this, and I believe every other possible combination, and the right front turn signal STILL does not work.
Additional info:
-I checked the fuse box by the battery and the 4 fuses were fine.
-I tried comparing it to the left front turn signal, but there are only two wire connectors, not 4.
-The right turn signal indicator (on the dash) works fine, as does the rear right turn signal.
Any ideas?
What is the correct wiring connections -what goes with RED and what goes with BLACK on the turn signal (if not what I mentioned), or what else could be an issue.
Thanks!
Comment
-
wiring picture
and here is a photo.
In the bottom, you can see the wires which come from the turn signal. A Black (with white stripe) wire, and a Red wire.
In the top right of the photo you can see the four other wires which lead from the handlebar. They seem to be paired in two. At the top, a yellowish wire with a Black (with white stripe) wire. Just below that, a greenish wire with a Black (with white stripe) wire.
Following the wiring diagram, I used the yellowish wire as the pink wire (figuring the pink faded), and connected it to the Black/white stripe wire coming from the turn signal. I then used the greenish wire to connect to the Red wire coming from the turn signal.
It did not work...Attached Files
Comment
-
I don't see a red wire in the wiring diagram for your bike. I do know that black/white should go to black/white. The diagram for your bike says black to green.
I would go green to red after that as it may be an aftermarket replacement housing. If it doesn't work, check the bulb.
To reiterate:
Green and black/white pair goes:
Green to red
Black/white to Black/white
Originally posted by latenight View Postand here is a photo.
In the bottom, you can see the wires which come from the turn signal. A Black (with white stripe) wire, and a Red wire.
In the top right of the photo you can see the four other wires which lead from the handlebar. They seem to be paired in two. At the top, a yellowish wire with a Black (with white stripe) wire. Just below that, a greenish wire with a Black (with white stripe) wire.
Following the wiring diagram, I used the yellowish wire as the pink wire (figuring the pink faded), and connected it to the Black/white stripe wire coming from the turn signal. I then used the greenish wire to connect to the Red wire coming from the turn signal.
It did not work...
Comment
-
Originally posted by latenight View PostThanks for the suggestion. Both the wiring, and the need to look at the key!
I hooked it up as you suggested and it worked immediately!
Out of curiosity... any idea what the other two dangling wire connectors are?
Comment
Comment