If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
when i painted mine a few months back i used half a litre of black 2pack paint and this was mixed with activator and a little thinners. in total i had just over 3/4 of a litre and this did the wheels also. i then used around the same in clear cote.
so in total i bought 1/2 litre of black paint, 1/2 litre of clear cote , 1/2 litre of activator and i bought 2 litres of thinners as you will use this to clean the gun ect ect.
Didn't anybody teach you guys how to spell "liter"?
Just playing. I had to throw at least one Yank post into your UK thread!
Any and all statements by Loudnlow7484 are merely his own opinions, and not necessarily the opinion of Katriders.com. Anything suggested by him is to be followed at your own risk, and may result in serious injury or death. Responses from this member have previously been attributed to all of the following: depression, insomnia, nausea, suicidal tendencies, and panic. Please consult a mental health professional before reading any post by Loudnlow7484.
Most paints come with the need for reducer, which is "usually" a 2 to 1 ratio. You could technically paint a piece such as (cowl size) if your experienced and have the proper equipment, but you would only need a 2oz bottle after you add reducer, if that gives you an idea.
If you are looking to do red with a black metal flake, I would suggest doing a red base that is close to the color you want, then add your red with black flake on top of that, it will allow you to use less paint, and allow the flake to sit up on top. Hope that helps!
Your right Mojoe, sorry that was a mistake on my end, it is a 1:1. Didn't even realize it when I was typing that up. But yes a pint should be plenty, especially if you use a base that matches the color pretty well, or a good primer.
Most paints come with the need for reducer, which is "usually" a 2 to 1 ratio. You could technically paint a piece such as (cowl size) if your experienced and have the proper equipment, but you would only need a 2oz bottle after you add reducer, if that gives you an idea.
If you are looking to do red with a black metal flake, I would suggest doing a red base that is close to the color you want, then add your red with black flake on top of that, it will allow you to use less paint, and allow the flake to sit up on top. Hope that helps!
Have you used metal flake before? I'm planning on painting my tank with a flake and this is the method I've seen and been told to use.
In my experience you need to lay your base, add a mid clear (usually two coats) and then lay your clear with the flake mixed according to taste. Then you need to use the mid clear to bury the flake and make sure it all "lays" properly then on top you'll clear it.
You need to make sure the flake lays properly or it will sit above your clear and when you go to wetsand and such it will mess it up.
Have you used metal flake before? I'm planning on painting my tank with a flake and this is the method I've seen and been told to use.
In my experience you need to lay your base, add a mid clear (usually two coats) and then lay your clear with the flake mixed according to taste. Then you need to use the mid clear to bury the flake and make sure it all "lays" properly then on top you'll clear it.
You need to make sure the flake lays properly or it will sit above your clear and when you go to wetsand and such it will mess it up.
That's how we did it. The flake always went in the first coat of clear. Then it's just a matter of doing enough coats of clear to smooth it all (PITA on jumbo flakes), followed by wetsanding. I can't imagine you'd be able to see the flake too much if you put it in the base. I've never tried, though, so I don't know.
Any and all statements by Loudnlow7484 are merely his own opinions, and not necessarily the opinion of Katriders.com. Anything suggested by him is to be followed at your own risk, and may result in serious injury or death. Responses from this member have previously been attributed to all of the following: depression, insomnia, nausea, suicidal tendencies, and panic. Please consult a mental health professional before reading any post by Loudnlow7484.
The flake doesn't get put in the base. It gets put on after the base in what's called a mid clear, that's where you lay the flake. Then you use a top clear.
If you've done it that way with good results, that's awesome. That's why I was asking, since all I've heard is bury it in a mid clear then clear over the mid clear. That way unless you burn through the layers of top clear there's no chance of harming the burried flake.
Comment