WARNING:This is not a mod that is done by itself. You should do a rear shock upgrade at the least also!
Now with that said, you will have to start out with a Katana, pre or post 1998
For the pre you will need the following
1999-2007 Hayabusa front forks or 2008-present Hayabusa front forks
1999-2007 Hayabusa front wheel or 2008-present Hayabusa front wheel
1999-2007 Hayabusa front rotors and calipers or 2008-present Hayabusa front calipers
1999-2007 Hayabusa front brake lines (preferably Stainless Steel) or 2008-present Hayabusa front brake lines
You can use your mastercylinder with these brakes
1999-2007 Hayabusa front fender or 2008-present Hayabusa front fender
1999-2007 Hayabusa front axle or 2008-present Hayabusa front axle
Make completely sure you have all the small hardware to go with all these parts mentioned!
On the pre 1998 katanas you will also need a new speedometer, post 98 sprocket cover and speed sensor ( some wiring required)
If you look at any parts fische, you will see that the bearings are completely different on the 99-07 Busa and the 08-present than the Katana. The Katana Lower will work on either Busa setup, it is press fit. As for the top bearing, will have to be a 30mm X 47mm X 15mm Tappered bearing. I found mine and Mreedohio's at http://www.twfracing.com/zparts.html
I also believe that this can be found thru other avenues.
You will have to remove the steering dampener tab, like I show in this picture. This has to be removed so that the headlight and it don't interfer with each other. You will have to come up with a good idea for a steering stop also.
If anything was missed, I appologize now and can answer any questions you might have.
Mreedohio can help a little also!
Now with that said, you will have to start out with a Katana, pre or post 1998
For the pre you will need the following
1999-2007 Hayabusa front forks or 2008-present Hayabusa front forks
1999-2007 Hayabusa front wheel or 2008-present Hayabusa front wheel
1999-2007 Hayabusa front rotors and calipers or 2008-present Hayabusa front calipers
1999-2007 Hayabusa front brake lines (preferably Stainless Steel) or 2008-present Hayabusa front brake lines
You can use your mastercylinder with these brakes
1999-2007 Hayabusa front fender or 2008-present Hayabusa front fender
1999-2007 Hayabusa front axle or 2008-present Hayabusa front axle
Make completely sure you have all the small hardware to go with all these parts mentioned!
On the pre 1998 katanas you will also need a new speedometer, post 98 sprocket cover and speed sensor ( some wiring required)
If you look at any parts fische, you will see that the bearings are completely different on the 99-07 Busa and the 08-present than the Katana. The Katana Lower will work on either Busa setup, it is press fit. As for the top bearing, will have to be a 30mm X 47mm X 15mm Tappered bearing. I found mine and Mreedohio's at http://www.twfracing.com/zparts.html
I also believe that this can be found thru other avenues.
You will have to remove the steering dampener tab, like I show in this picture. This has to be removed so that the headlight and it don't interfer with each other. You will have to come up with a good idea for a steering stop also.
If anything was missed, I appologize now and can answer any questions you might have.
Mreedohio can help a little also!
Comment