CAN ANYONE TELL ME WHETHER OR NOT I CAN CONVERT GSXR PARTS, LIKE FOR INSTANCE, WILL GSXR CARBS BOLT ON TO MY KAT FOR MORE PROFORMANCE? IF ANYONE KNOWS STUFF ABOUT THIS LET ME KNOW PLEASE!!!!!!!!!!!
Ad Widget
Collapse
Announcement
Collapse
No announcement yet.
X
-
CONVERTING PARTS
Jeeps and Katanas are all you need to live, you have the off road experience on one side, then you can go home and tear down the street. Plus girls like jeeps and bikes. Looking to upgrade my 600, anyone who knows mods on my bike, let me knwo some things I can do to make it faster. [email protected]Tags: None
-
Re: CONVERTING PARTS
Originally posted by KATANA600BLUECAN ANYONE TELL ME WHETHER OR NOT I CAN CONVERT GSXR PARTS, LIKE FOR INSTANCE, WILL GSXR CARBS BOLT ON TO MY KAT FOR MORE PROFORMANCE? IF ANYONE KNOWS STUFF ABOUT THIS LET ME KNOW PLEASE!!!!!!!!!!!
The modern GSXR is a purpose-built bike whose primary design-purpose is track performance. It weighs 100 lbs less than the Katana, uses water-cooling to suck away heat faster from the engine (which permits higher compression ratios and higher heat building caused by higher RPM ceilings), uses lighter reciprocating parts (the parts that move) to give it a higher RPM ceiling.
The Katana (GSXF) is also a purpose-built bike, but one whose purpose is real world riding comfort and reliability (sport-tourer). It's longer and weighs more, which gives it more straight-line stability at speed and better ability to suck up bad pavement (better unsprung vs sprung weight ratios). The katana is oil cooled (sheds the need for water pump, water radiator, thermostat, water, all sources of additional maintenance and failures on the road), has a lower compression ratio (good for engine longevity). The current generation Katana has bigger fairings (better wind & weather protection), and is more comfortable for most riders.
You may also want to read this thread on water vs. oil-air cooled engines: http://www.katriders.com/forums/viewtopic.php?t=10071
There is simply no way to bolt items from a modern GSXR onto a Katana and get it to suddenly be as zippy as the GSXR; there are too many differences that can't be readily changed (like the weight). Additionally, almost all current-generation GSXR parts won't fit -- and those that do are unlikely to give you any power benefit.
You have a few options:
(A) You can install a substancially bigger engine into the Katana (such as an 1100 or 1200 engine), which increases the total power output of the bike by replacing the motor... This will add a lot of power, but still won't carve 100 lbs off your bike (actually, you'll be adding some weight).
(B) You can redo the existing engine (wiseco engine kits) to increase both the displacement and compression ratios, netting you more power (such as WiseCo's 771 or 813cc kits). This will increase your power levels, but still won't carve that extra 100 lbs off the bike.
(C) You can add some power to the existing engine by adding in a jetkit, an ignition advancer, possibly some intake and exhaust modifications, BUT ALL OF THESE WILL ONLY NET YOU MINOR INCREASES.
(D) You can resprocket the front and rear sprockets, which will trade off some top speed for faster off-the-line times.
or what I would recommend for you, based on this and other posts:
(E) Sell you Kat. Buy a GSXR. It is the bike you really seem to want.
Cheers
=-= The CyberPoet
Comment
-
Re: CONVERTING PARTS
Originally posted by KATANA600BLUECAN ANYONE TELL ME WHETHER OR NOT I CAN CONVERT GSXR PARTS, LIKE FOR INSTANCE, WILL GSXR CARBS BOLT ON TO MY KAT FOR MORE PROFORMANCE? IF ANYONE KNOWS STUFF ABOUT THIS LET ME KNOW PLEASE!!!!!!!!!!!
Comment
-
Take off the center stand...that will reduce weight..but like Cyber said...if you want a GSXR then your best bet is to buy one...I agree the Kat is a ton more comfortable to ride...now one thing I did hear my mechanic say is some people replaced the Kat cam with a GSXR cam and it gave substancially more power to the Kat engine..any truth to that???...but you still have that 100lbs difference or 80lbs if you remove the center stand...Good judgement comes from experience, and often experience comes from Bad Judgement :smt084
Help Support Katriders.com via Motorcyclegear.com
Welcome to KatRiders.com! Click here to Register
nah nah nah nah nah nah JAX! (special thnx to sexwax)
Comment
-
Jax, I find it doubious that just swapping cams will net you more power (because the GSXR cam lift & duration is actually designed for an engine that revs substancially higher and doesn't make peak power until the RPM ceiling for the Kat has already been hit)...
As for the centerstand, I recall someone weighing it and saying 8.5 lbs or so... You can put your Kat on a diet, but it's not going to lose 100 lbs no matter how hard you starve it.
Cheers
=-= The CyberPoet
Comment
-
how much power does the WiseCo's 771 or 813cc kits produce in comparison to the engine swaps? i only weigh 135. my buddy has a 2004 600 gsxr and weighs 190. sooooo 55- 8 (center stand) =47 more lbs to knock off. hummmmm 1 gallon of gas weighs 7 lbs........
Comment
-
Originally posted by smoubarahow much power does the WiseCo's 771 or 813cc kits produce in comparison to the engine swaps? i only weigh 135. my buddy has a 2004 600 gsxr and weighs 190. sooooo 55- 8 (center stand) =47 more lbs to knock off. hummmmm 1 gallon of gas weighs 7 lbs........
Stock GSX600F (11.2:1 ratio): 70 HP at the rear wheel
Stock GSX750F (10.5:1 ratio): 80 HP at the rear wheel
771cc (13:1 ratio): 93 HP at the rear wheel (my rough estimate)
813cc (12.5:1 ratio): 100 HP at the rear wheel (again, my rough estimate)
Stock Bandit 1200 (1157cc, 9.5:1 ratio) engine: 90 HP at the rear wheel (estimated) -- mods to this engine can yield 110 - 150 HP readily.
I'm sure some of the guys around here have these kits installed and can pop off dyno numbers for their own bikes, but remember that dyno numbers reflect a lot of variables (from chain condition to ambient temp & humidity, as well as tire size), so you can't compare one dyno's output to another's fairly.
Cheers
=-= The CyberPoet
Comment
-
And every dyno is different . One dyno's 100hp may be another's 90-ish . I had mine dyno-ed back in spring and only showed 90hp . This is with a 771 , VERY poor jetting , and a chain that looked to be aligned by a blind monkey (oops ) . I've since read about another guys 771ed Kat getting a little over 100hp .
Comment
-
Re: CONVERTING PARTS
Originally posted by The CyberPoetOriginally posted by KATANA600BLUECAN ANYONE TELL ME WHETHER OR NOT I CAN CONVERT GSXR PARTS, LIKE FOR INSTANCE, WILL GSXR CARBS BOLT ON TO MY KAT FOR MORE PROFORMANCE? IF ANYONE KNOWS STUFF ABOUT THIS LET ME KNOW PLEASE!!!!!!!!!!!
The modern GSXR is a purpose-built bike whose primary design-purpose is track performance. It weighs 100 lbs less than the Katana, uses water-cooling to suck away heat faster from the engine (which permits higher compression ratios and higher heat building caused by higher RPM ceilings), uses lighter reciprocating parts (the parts that move) to give it a higher RPM ceiling.
The Katana (GSXF) is also a purpose-built bike, but one whose purpose is real world riding comfort and reliability (sport-tourer). It's longer and weighs more, which gives it more straight-line stability at speed and better ability to suck up bad pavement (better unsprung vs sprung weight ratios). The katana is oil cooled (sheds the need for water pump, water radiator, thermostat, water, all sources of additional maintenance and failures on the road), has a lower compression ratio (good for engine longevity). The current generation Katana has bigger fairings (better wind & weather protection), and is more comfortable for most riders.
You may also want to read this thread on water vs. oil-air cooled engines: http://www.katriders.com/forums/viewtopic.php?t=10071
There is simply no way to bolt items from a modern GSXR onto a Katana and get it to suddenly be as zippy as the GSXR; there are too many differences that can't be readily changed (like the weight). Additionally, almost all current-generation GSXR parts won't fit -- and those that do are unlikely to give you any power benefit.
You have a few options:
(A) You can install a substancially bigger engine into the Katana (such as an 1100 or 1200 engine), which increases the total power output of the bike by replacing the motor... This will add a lot of power, but still won't carve 100 lbs off your bike (actually, you'll be adding some weight).
(B) You can redo the existing engine (wiseco engine kits) to increase both the displacement and compression ratios, netting you more power (such as WiseCo's 771 or 813cc kits). This will increase your power levels, but still won't carve that extra 100 lbs off the bike.
(C) You can add some power to the existing engine by adding in a jetkit, an ignition advancer, possibly some intake and exhaust modifications, BUT ALL OF THESE WILL ONLY NET YOU MINOR INCREASES.
(D) You can resprocket the front and rear sprockets, which will trade off some top speed for faster off-the-line times.
or what I would recommend for you, based on this and other posts:
(E) Sell you Kat. Buy a GSXR. It is the bike you really seem to want.
Cheers
=-= The CyberPoet
Comment
-
Originally posted by The CyberPoetOriginally posted by smoubarahow much power does the WiseCo's 771 or 813cc kits produce in comparison to the engine swaps? i only weigh 135. my buddy has a 2004 600 gsxr and weighs 190. sooooo 55- 8 (center stand) =47 more lbs to knock off. hummmmm 1 gallon of gas weighs 7 lbs........
Stock GSX600F (11.2:1 ratio): 70 HP at the rear wheel
Stock GSX750F (10.5:1 ratio): 80 HP at the rear wheel
771cc (13:1 ratio): 93 HP at the rear wheel (my rough estimate)
813cc (12.5:1 ratio): 100 HP at the rear wheel (again, my rough estimate)
Stock Bandit 1200 (1157cc, 9.5:1 ratio) engine: 90 HP at the rear wheel (estimated) -- mods to this engine can yield 110 - 150 HP readily.
Dale Walkers Holeshot bandit 1200 has the following specs
Engine
Holeshot/JE 1216cc piston kit
Holeshot cylinder head porting & comp valve job
GSX-R intake cam
Holeshot Stage 2 jetting
Holeshot 5 degree timing advancer
Holeshot HD clutch spring
Exhaust
Holeshot complete stepped system with new high pipe
Dale is getting 150HP at the rear wheel with 96ft/lbs of torque
Comment
Comment