I have a 1993 Suzuki Katana 600 with 16000 miles on it and I am the second owner. About 2 week ago I snapped the chain, which was the original. I ordered a new chain and took off the rear wheel and put the new chain on. Now the nut on the tension adjuster on the opposite side of the chain keeps coming loose and backing off causing the back tire to come out of alignment. I went to the local motorcycle shop and they told me the nylon on the inside of the nut must be worn out and they gave me a new nut. I put it on and snugged it tight against the old one and made sure the tire was aligned properly. I also made sure the castle nut was still tight and it was. I checked it today and found that it has backed off once again, any ideas what could be causing this? It never did this before I took the back wheel off, so I am wondering if I did something wrong?
Ad Widget
Collapse
Announcement
Collapse
No announcement yet.
X
-
Lets see...
If the adjuster itself is moving backwards, the axle is not properly tightened. If it were, the adjuster would not move, even if the nut was lose. Tighten properly the axle, then even if the nut goes flying away, the rear tire should not come out of alignment.
If the nut is properly tightened, and the axle to, there is no way in hell you would need to locktite it.Ich lebe mein Tod, Tag für Tag!
Willkommen zu meiner Welt...
Comment
-
Originally posted by Süsser TodLets see...
If the adjuster itself is moving backwards, the axle is not properly tightened. If it were, the adjuster would not move, even if the nut was lose. Tighten properly the axle, then even if the nut goes flying away, the rear tire should not come out of alignment.
If the nut is properly tightened, and the axle to, there is no way in hell you would need to locktite it.I don't have a short temper. I just have a quick reaction to bullshit.
Comment
-
I can tighten the axle more, I just don't want to go to far, or can I go to far? This is my first bike, and I don't know too much about them, just hands-on learning. If the axle is properly tightened, could you still tighten the nuts and have the adjuster move the axle? How would I know how far to tighten the axle. It's at the point now where the cotter pin doesn't fit into the grooves on the castle nut. I checked all over the work area in my garage and there are no missing parts, so I don't know what to do about it now.
Comment
-
Originally posted by MojoeOriginally posted by Süsser TodLets see...
If the adjuster itself is moving backwards, the axle is not properly tightened. If it were, the adjuster would not move, even if the nut was lose. Tighten properly the axle, then even if the nut goes flying away, the rear tire should not come out of alignment.
If the nut is properly tightened, and the axle to, there is no way in hell you would need to locktite it.
Originally posted by czycoot1318It's at the point now where the cotter pin doesn't fit into the grooves on the castle nut. I checked all over the work area in my garage and there are no missing parts, so I don't know what to do about it now.
You'd have to try really hard to go "too far"
tighten that bastage up.. just remember, with a long breaker bar, a lot of effort is not necessary..
Comment
-
just be careful when you tighten with a breaker bar. do it with the breaker bar towards the front of the bike and push down....not with the bar facing the rear and pulling up. If you do it that way, you can push the bike off the centerstand if you have one....and probably the sidestand as well.
I know this cuz I did it once. I knocked it right off the centerstand....and was a very lucky mofo to catch the bike before it toppled over.
Now I just use an impact gun.I don't have a short temper. I just have a quick reaction to bullshit.
Comment
Comment