KOTM Dec 2008 waveman
 

Welcome to the KatRiders.com forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Go Back   KatRiders.com > Service Department > Katana How-To's & FAQ's

Katana How-To's & FAQ's A forum filled with write-ups, FAQ's, and visual aids for
mechanical & cosmetic modifications to your Katana.

Reply
 
Thread Tools Display Modes
Old 03-06-2005, 11:26 PM   #1
meanstrk
Kat Champion
 
Join Date: Dec 2004
Location: Carthage, NC
Posts: 1,995

Default Poor man's ignition advancer. Do it yourself

Poor man's ignition advancer,

No cost, just a little bit of time.......
So, how much should you enlarge the holes and twist the plate? Well the advance should be 3-5 and 1 is almost exactly 1mm on the edge of the plate. So enlarge the holes about 5mm. The best way to find the optimum setting is to dynotest the bike and try different settings. The advance units you can purchase, usually have a fixed setting of 5. Be carefull not to over do it and listen for engine "pre detonation" which usually occurs at low RPM, high gear and high load. On an otherwise low tuned engine you could expect about 1-2 Hp in the midrange.

Diagram:




Now, what I did on my Kat in addition to the above, was I also scribed degree lines in the plate at 0 degrees, 2.5 degrees, and 5 degrees, and then used the engine block as a pointer. You can see on the right side where the lines are scribed. Most advancers run 4 to 5 degrees advance. I use 3 degrees. Note that this pic was taken at 0 degrees advance.

http://www.bikepics.com/pictures/304533/
__________________
Ron
MSgt, USMC (Retired)

Last edited by meanstrk; 03-10-2009 at 01:53 PM..
meanstrk is offline   Reply With Quote
Old 03-06-2005, 11:34 PM   #2
ThAzKat
KatBusa Owner
 
ThAzKat's Avatar
 
Join Date: Nov 2004
Posts: 9,844
eBay ID: ThAzkat93

Default

Thanks bro, good info!
__________________
TDA Racing/Motorsports
1982 Honda CB750 Nighthawk, 1978 Suzuki GS750 1986 Honda CBR600 Hurricane; 1978 Suzuki GS1100E; 1982 Honda CB750F supersport, 1993 Suzuki Katana GSX750FP. 1981 Suzuki GS1100E (heavily Modified) http://katriders.com/vb/showthread.php?t=94258
Who knows what is next?
Builder of the KOTM Mreedohio september winning chrome project. I consider this one to be one of my bikes also!
Please look at this build! http://katriders.com/vb/showthread.php?t=91192
ThAzKat is offline   Reply With Quote
Old 03-07-2005, 12:56 AM   #3
WildKat
Bring Back the '80s
 
WildKat's Avatar
 
Join Date: Oct 2004
Location: York, PA.
Posts: 13,513
eBay ID: wildkat129

Default

good thinkin, thanks for the info! I'll stickify it for awhile !
__________________
WildKat is offline   Reply With Quote
Old 03-07-2005, 01:55 AM   #4
arsenic
Katastical
 
arsenic's Avatar
 
Join Date: Nov 2004
Location: 60505
Posts: 21,181
eBay ID: arsenic1016

Default

Why did I think of that. Good info bro.
__________________


DREAM Katana

arsenic is offline   Reply With Quote
Old 03-07-2005, 03:20 AM   #5
UFO8MyCow
Kat Champion
 
UFO8MyCow's Avatar
 
Join Date: Dec 2004
Location: Blaine, mn
Posts: 1,707
eBay ID: Cgstrong

Default

Does it only work on kats or all bikes?
__________________
PM me for Ultrasonic Carb Cleaning, pilot screw o-rings and washers and mercury refills

Harley Davidson
The most efficient way to turn gasoline into noise without the biproduct of horsepower
UFO8MyCow is offline   Reply With Quote
Old 03-07-2005, 04:36 AM   #6
meanstrk
Kat Champion
 
Join Date: Dec 2004
Location: Carthage, NC
Posts: 1,995

Default

It can work on any bike that has a rotating advancer and stationary pickup and a backing plate that can be removed. In effect, it's like rotating a distributor on a car.
meanstrk is offline   Reply With Quote
Old 03-08-2005, 07:59 PM   #7
Gripp
Katrider
 
Join Date: Jan 2005
Posts: 227

Default

Won't advancing the timing increase popping thru the exhuast on decel, or does it just effect top end?
__________________
Gripp & Regripp
Gripp is offline   Reply With Quote
Old 04-15-2005, 04:53 PM   #8
TemtnF8
Katrider
 
Join Date: Apr 2005
Location: Seattle, WA
Posts: 194

Default

I had an idea to go along with this... Couldn't you just enlarge the size of the gap on the back of the OEM rotor by 5 degrees or so in the correct direction and re-attach it? This would be much easier/cheaper to fix if you mess something up, and I'm sure any machine shop could take care of it in 20 minutes for $10-20.
TemtnF8 is offline   Reply With Quote
Old 06-28-2005, 11:01 AM   #9
Special K
Kat Master
Founding Member
 
Join Date: Oct 2004
Location: Kernersville, NC
Posts: 3,244

Default

The only problem I've seen with this method is its REALLY tough to find 1 degree differences using this, as its adjustable.

You can get the good ones for only $46 delivered to most states...............as an alternative! 8)
__________________
I've owned over 70 Katanas - you think I know anything about them?
Is there such a thing as TOO MANY BIKES?
Can you go TOO FAST on a bike?
Welcome to KatRiders.com! Click here to register
Special K is offline   Reply With Quote
Old 11-07-2005, 10:20 AM   #10
paulos
Chicken Strip
 
Join Date: Nov 2005
Location: Telford,UK
Posts: 18

Default

i'd like to do this mod but unfortunately the pictures don't work so i haven't got a clue????
paulos is offline   Reply With Quote
Sponsored Links
Reply

  KatRiders.com > Service Department > Katana How-To's & FAQ's

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Poor-man's jetkit kjcmetal Exhaust & Mod Shop 8 07-07-2008 10:14 PM
Poor man's exhaust Rok_Stars_Bars Katana How-To's & FAQ's 21 10-24-2007 10:43 AM
poor mans ignition advancer question IForgotMyUserName2 Mechanics 101 19 06-16-2007 02:43 AM
Potential poor man's speed bleeder? josepaz2 All About Brakes & Suspension 2 05-31-2007 06:19 AM
Poor man's corbi? versionpardner Suzuki Katana Talk 8 05-04-2007 12:14 PM

All times are GMT -5. The time now is 07:16 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Katriders.com, Copyright ©2004 - 2017

Like Cigars? Check out Vitola.org